Correct use of Luring - Printable Version +- OTBots Forums (https://forums.otbots.com) +-- Forum: Nostalrius OTBot (https://forums.otbots.com/Forum-Nostalrius-OTBot--90) +--- Forum: Support (https://forums.otbots.com/Forum-Support--95) +--- Thread: Correct use of Luring (/Thread-Correct-use-of-Luring--1601)

Correct use of Luring - otezerobotter - 03-09-2021 Hi there! I would like to make an script to lure 3+ mobs and kill then using exori and chase offensive. To exori this is working fine: |Only Registered members can see download links. | Click here to buy subscription or here to register. In Target i did setup for mob i want to kill: Count: 2+ (lure 2+ monster to a specific spot) Stance: Lure Atk Mode( Chase ofensive, i want the bot to kill chasing then when reach lure spot). In Cavebot i have used 1 lure waypoint ( spot that i want the bot to lure mobs to) and then 3 stand positions where the mobs are, i want it to go over the stands luring and when reach lure spot stop and kill. The issue is that the bot keeps running around and never stops at lure spot, im doing something wrong? I want the bot to go towards the stand waypoints and lure mobs until reach lure, when it reach lure kill all mobs using exori and chase/offensive so mobs do not run away. RE: Correct use of Luring - Arkilys - 03-10-2021 Hello. Why are you using client's change (Atk Mode -> Chase) with a Stance? You should setup it as "Stand", so there will be no conflicts. Otherwise, bot will try to go to lure wpt and client's chase will try to reach monster. If you wanna kill with "Chase" or "Reach" then you should use: Setting1 --Hp: 20 to 100 --Stance: Lure --Atk Mode: Stand (doesn't matter if offensive or so). Setting2 --Hp: 0 to 20 --Stance: no stance --Atk mode: Chase RE: Correct use of Luring - otezerobotter - 03-10-2021 I did as the setup says so, the bot is respecting and stoping at correct spot but it does not chase the dragons when low hp. I`ve tried to put also 0-25% hp at setting2 and did not worked. RE: Correct use of Luring - Arkilys - 03-10-2021 Hello. You certainly did not. You should setup exactly like I said, but you can adjust hp ranges, however if you adjust hp range then you must adjust on both settings. Setting1 --Hp: 20 to 100 --Stance: Lure --Atk Mode: Stand (doesn't matter if offensive or so). Setting2 --Hp: 0 to 20 --Stance: no stance --Atk mode: Chase Send me your .xml settings. RE: Correct use of Luring - otezerobotter - 03-10-2021 |Only Registered members can see download links. | Click here to buy subscription or here to register. Now its luring correctly to a spot, but when it starts to kill dragons if i put 3+ dragons when it kills one of then it will run through waypoints again with 2 dragons in middle life, i want it to kill all dragons that was lured and then go to next waypoint. RE: Correct use of Luring - Arkilys - 03-11-2021 That's because of "Count" that you setup. If you wanna lure and then kill with chase no matter how many dragons there are then you should setup "Count" = Any. If you wanna lure only when there are 3+ then you should create two dragon entries. 1st. Dragon -> Count: 3+ -> Setting1 -> 50% to 100% / Stance: Lure / Danger: 1; Setting2: 0 to 50% / Stance: No stance / Atk mode: Chase / Danger: 1; 2nd entry. Dragon -> Count: Any -> Setting1 -> 0 to 100% / Danger: 0; So your targeting list will look like: Dragon (3+) Dragon (Any) Dragon Lord